Spooky2 provides several presets for your ease of use. Below are explanations to each preset that help you choose the one that suits you most.

JW - Colloidal Silver Generation

These are John White's recommended settings for generating Colloidal Silver. A range of nano-sized silver particles will be created. Use the Colloidal Silver waveform. The Spooky2 calculator will provide an estimate of the dwell. Set the Dwell Multiplier to the number of minutes you wish to run the program. Connect the silver rods to a Spooky Boost v2.0.

The quality of CS will increase if it is made slowly. It can take over a day to make a great batch. Regular stirring will improve results. An electrical stirrer gives best results.

Use cold distilled water. Hot water will speed up the process but the particle size will increase. The rods may turn dark. This is normal and will not adversely affect the quality of the Colloidal Silver. Clean the rods between batches.

When the CS solution is ready it may be clear or a light straw color. This indicates a very small particle size. You can shine a laser light in the solution and see a visible red line, indicating microscopic silver particles in suspension. Let the solution stand for a few hours before bottling. This allows any silver nitrates to settle to the bottom.

Store the CS solution in a dark glass container at room temperature. Do not refrigerate.

JW - cpsResearch LLC DNA Frequencies (Contact)

These are John White's recommended settings for applying Char Boehm's DNA frequency sets in contact mode. When an octal subharmonic of an MOR is known it is best to apply an inverted sawtooth waveform targetting the highest subharmonic possible. These settings will do this, with up to 20 MHz being applied.

JW - cpsResearch LLC DNA Frequencies (Remote)

These are John White's recommended settings for applying Char Boehm's DNA frequency sets in remote mode. When an octal subharmonic of an MOR is known it is best to apply an inverted sawtooth waveform targetting the highest subharmonic possible. These settings will do this, with up to 20 MHz being applied.

JW - Healing (Contact)

These are John White's recommended settings for healing frequency sets. Healing frequencies should be applied using either square waves or sine waves.

JW - Healing (Remote)

These are John White's recommended settings for healing frequency sets. Healing frequencies should be applied using either square waves or sine waves.

JW - Killing (Contact)

These are John White's recommended settings for killing viruses / bacteria. Inverted sawtooth waveforms contain both even and odd harmonics. All octal harmonics are hit. Of proven biological benefit is the sharp rising edge which applies stress to the target pathogen.

JW - Killing (Remote)

These are John White's recommended settings for killing viruses / bacteria. Inverted sawtooth waveforms contain both even and odd harmonics. All octal harmonics are hit. Of proven biological benefit is the sharp rising edge which applies stress to the target pathogen.

JW - Papimi Killing (Contact)

Use this program for high frequencies only. Use JW-Killing for most database entries.

JW - Papimi Killing (Remote)

Use this program for high frequencies only. Use JW-Killing for most database entries.

JW - Spooky Central

Basic settings for Spooky Central.

Out 1 to Input. Out 2 to Modulation.

JW - Spooky Central Beat Frequencies

Optimized for Spooky Central to run database frequencies less than 1.75 MHz (1750000 Hz). A beat frequency is created that equals the database frequency. This has proven beneficial for most database sets.

Out 1 to Input. Out 2 to Modulation.

JW - Spooky Central Cancer

Preset for targeting Cancer using Spooky Central.

Out 1 to Input. Out 2 to Modulation.

JW - Spooky Central Cancer (with carrier)

Preset to target generic cancer using a carrier. The first sidebands simultaneously hit both BX & BY.

Connect Out1 to Input. Out2 to Modulation.

JW - Spooky Central Cancer Overnight Sweep

This Preset has been optimised to apply power maximum power in the Cancer frequencies. Use with caution. Place the plasma tube near to your body. Ensure the tube has free ventilation.

Out 1 to Input. Out 2 to Modulation.

JW - Spooky Central Overnight Sweep High Frequency

Run this preset overnight. Power is focused around 1.6 MHz, but all frequencies are targeted.

Place the plasma tube near to your body. Ensure the tube has free ventilation. Overall duration is 8 hours 35 minutes. Do not apply more than 5 volts to the inputs.

Out 1 to Input. Out 2 to Modulation.

JW - Spooky Central Overnight Sweep Low Frequency

Run this preset overnight. Power is focused more around 100 kHz, but all frequencies are targeted.

Place the plasma tube near to your body. Ensure the tube has free ventilation. Overall duration is 8 hours 25 minutes. Do not apply more than 5 volts to the inputs.

Out 1 to Input. Out 2 to Modulation.

JW - Spooky Central Overnight Sweep Med Frequency

Run this preset overnight. Power is focused more around 1 MHz, but all frequencies are targeted.

Place the plasma tube near to your body. Ensure the tube has free ventilation. Overall duration is 8 hours 45 minutes. Do not apply more than 5 volts to the inputs.

Out 1 to Input. Out 2 to Modulation.