Zapping, the Spooky2 Way 9

Share this:

Most people think that using electricity to heal is a recent innovation, but electricity was used in conjunction with acupuncture back in 1890. A little before this (2000 years to be more precise) batteries were discovered that researchers think may have been used for acupuncture and to anesthetize skin prior to surgery.

Flash forward to the 1920s, when a brilliant scientist called Royal Rife found that nasty viruses and bacteria could be quickly destroyed if the correct frequency and application method is used. To this day we are struggling to repeat his success.

More recently Dr. Hulda R. Clark developed simpler and cheaper methods of applying frequencies to the body. She wrote the book “The Cure of all Diseases” and several other titles. Her research was focused on low technology solutions to often very serious illnesses.

Dr. Clark believed that parasites are destroyed if a weak pulsing DC is applied, so she developed the “zapper”. These zappers typically run off 9 volts and use primitive electronics. They are safe because the amount of current that enters the body is low and Dr. Clark recommends a maximum treatment time of 7 minutes. The pulsing DC frequency is not very important. Many people believe that zappers should run at 15 Hz. Others argue that higher frequencies of around 33 kHz are more effective. Good quality zappers often have a selection of frequencies to select from.

Spooky2 can very easily be turned into an advanced Zapper. The waveform is more effective than a simple pulsed DC.

(NOTE: What are your health conditions that need to be solved? Lyme, Pathogens or Human Energy Field?)

Here are two ways you can use suggested by Spooky2.

1. Go to Presets Tab, and search “zap” directly. Choose Zapper preset you want to run according to the description. Go to Control Tab, tick Overwrite Generator, open a generator button. After the frequencies are loaded, you can click Start button to start the treatment. It should be noted that the contents in the parentheses represent different modes. C represents Contact, P represents Plasma and etc. For example, if you want to run zapper in Remote mode with you GX, you can choose Zapper GX(R) – BY.

zapper preset

2. Go to Programs Tab, and search “zap”. Choose programs you want accroding to the description, and create your own preset to run these frequencies.

zapper programs

The First Way to Connect (Contact Mode):

Products: Spooky2-XM GeneratorSpooky2 Boost v3.1Spooky2 Tens CableSpooky2 Tens Pad

contact mode(TENS Pads)

The Second Way to Connect (Contact Mode):

Products: Spooky2-XM GeneratorSpooky2 Boost v3.1Spooky2 Tens CableSpooky2 Conductive Carbonized Rubber Hand Cylinders

contact mode(hand cylinders)

For greater safety, we recommend using the “Colloidal Silver” output of Spooky2 Boost v2.0. A safety resistor limits the current to very safe levels.

My personal view is that zappers have limited effectiveness. Dr. Clark died in 2009 from severe disease. Zappers may work for many medical issues, but they should be used in conjunction with several other protocols and lifestyle changes.

(NOTE: Are you new to Spooky2 Rife machine? Get Started Here!)

Share this:

9 Comments

  1. Will zapping the Spooky Way harm the microbiome, the good gut flora?

    1. It will not harm but it is also recommend to eat natural foods. Homemade fermented foods like Sauerkraut, Kim Chi, Miso, Pickles, Kefir, Kombucha and Yoghurt help to maintain gut flora biodiversity, which it turn assists in removing toxins. Foods with plenty of fiber to help your excretory system function smoothly.

  2. Excelente artigo, muito esclarecedor

  3. In remote mode, do you change the settings as it is listed in the description for Out 2 or run it with Killing JW?

    1. Hi, if you follow method 2, please follow descriptions to change the settings like amplitude, waveform and so on.

  4. hello, the presets say to use OUT1 for contact whilst the diagrams shows the boost 3.1. can you use boost for both or do the programs need boost 3 ?

    1. Hi, it depends on preset itself and please follow descriptions of the exact preset.

  5. Dear Spooky2 Team,

    There is a confusion here. The Zapper Presets (in version 20210225) all already contain a program called Zapper 1. This program can’t be found in the database. And when I run it, I see that the frequency is 2222.222. That seems a bit strange. Also there are two presets of Manuel Mallo in this version. Only they are empty (no program). In your article above, I can see that all the standard zapper presets also didn’t contain the program in the 2019 version.
    Can you update this article please and let us know what’s about Zapper 1 program?

    Thank you very much,

    Philippe

    1. Hi, our Spooky2 database has updated to the version of 20210917, you can download it to see this preset: https://www.spooky2.com/downloadspage/?_ga=2.88204827.1085051470.1635988092-1457904336.1630034316

Leave a Reply

Your email address will not be published.