Unlock the Power of Imprinting with Different Spooky2 Modes 2

Frequency imprinting is a simple way to transfer frequency programs onto materials such as water, essential oils, and holographic stickers. Once imprinted, these materials can be carried with you, making it easier to incorporate frequency-based wellness practices into your daily routine.

With Spooky2, frequency imprinting is not limited to a single method. Different application modes and setups can be used depending on the material and the way you prefer to work. In this blog, we’ll explore several common approaches to frequency imprinting using Spooky2 Contact, Remote, Scalar, PEMF, and Cold Laser modes.

Common Frequency Imprinting Methods

Contact Mode

1. Attach a pair of TENS pads to the outside of a glass container, positioning them on opposite sides so they face each other. Connect the pads to the High Power port on Spooky2 Boost using a TENS cable.
2. Choose a 20 V empty shell preset that corresponds to the programs you plan to use. In the Programs tab, set Dwell Multiplier to 0.333, tick Remove Duplicate Frequencies, and enable Apply Tissue Factor for MW and wavelength frequencies. 
3. Go to the Control tab, overwrite the corresponding generator, and start the imprinting process. Make sure to go through all the frequencies at least once. Running more cycles may help enhance stability.

Remote Mode

1. Clear any existing information from the holographic sticker using a strong magnet, then place the sticker inside the Spooky2 Remote.
2. Connect the Spooky2 Remote to the generator through the BN port on Spooky2 Boost. Choose a suitable Remote preset, or load your selected programs into an empty shell preset designed for Remote mode.
3. Go to the Programs tab. In the Options section, set Repeat Sequence = 0 to allow the preset to loop continuously, and tick Remove Duplicate Frequencies.
4. You can leave the Dwell Multiplier at the default value of 1, which allows each frequency to run for 180 seconds. Alternatively, set the value to 0.5 to reduce the dwell time by half.
5. Go to the Control tab, overwrite the corresponding generator, and click Start to begin imprinting. Make sure to run through all the programs for at least one complete cycle.
6. When the imprinting cycle completes, remove the sticker from the Remote before stopping the generator.

For more details, you can check this blog.

PEMF Mode

1. Position the BN side of the PEMF Coil facing the water, crystal, or other material you want to imprint. Alternatively, place a small vial inside the center of the coil.
2. Connect the PEMF Coil to the High Power port on Spooky2 Boost.
3. Select a suitable Coil preset, or load your chosen frequency program into an empty shell preset for PEMF mode. Based on user experience, PEMF imprinting is generally better suited to lower frequencies, such as 30 Hz.
4. Imprinting time may vary depending on the frequency used. Higher frequencies may take around 1–2 hours, while very low frequencies, such as the Schumann Resonance, may require one or two days of imprinting.

Cold Laser Mode

1. Place the Cold Laser accessory over the water or other material you want to imprint. Make sure the laser light shines directly onto the material.
2. Connect the Cold Laser accessory directly to the generator’s Out 1 port.
3. Choose a suitable Laser preset, or load your selected frequency programs into an empty shell preset for Cold Laser mode.
4. You can change Dwell Multiplier to 20 to imprint each frequency for an hour, and change to .05 for frequencies higher than 100 kHz to imprint within 10 seconds. Make sure to run through all loaded frequencies at least once. 
5. You can also use the Cold Laser and PEMF Coil together. Place the PEMF Coil below the material and the Cold Laser above it so both accessories are directed toward the item being imprinted.

Spooky2 Scalar

1. Place the object you want to imprint, such as a glass of water or a crystal, on the Transmitter coil of Spooky2 Scalar. You can also place substances you want to imprint from, such as essential oils, on the Receiver coil so their molecular information can be included in the imprinting process. Use lead-free glass containers whenever possible and avoid plastic containers. This helps minimize the possibility of unwanted material information being included during the imprinting process.
2. Tune the Spooky2 Scalar before beginning. In the Spooky2 software, choose a suitable Scalar preset from the Presets tab, or load your selected programs into the Spooky Scalar General (SS) – JW shell preset.
3. Click Start to begin imprinting. Make sure to run through all loaded frequencies at least once. You may remain within the Scalar field during the process if desired.
4. Imprinting time depends on the volume or size of the target object. A small container, such as a vial, may take only a few minutes, while larger containers or objects may require more time.

For more details, you can check this blog.