GeneratorX – Redefining Biofeedback 10

Share this:

GX changes the rules for biofeedback entirely. A biofeedback scan which takes an hour with Spooky Pulse now takes just over 4 minutes. Even less if you do not need to measure both current and phase angle. No more sitting (or lying) down forever, waiting for a biofeedback scan to complete. GX uses state-of-the-art components and ingenious circuit design to accurately monitor the current and phase angle of signals all the way up to 40 MHz. So you can really see what is happening in your body.

There is a contact mode biofeedback preset for GeneratorX in the 20180208 Spooky software. It may be the only biofeedback preset you need. Because it covers all frequencies ever discovered by Royal Rife, including the very high frequencies previously beyond reach of lesser machines. It detects the frequency of all the micro-organisms your body is unlucky enough to have.

GeneratorX can perform biofeedback scans much quicker than Spooky Pulse. There are two reasons:

1. GeneratorX is detecting electrical signals which travel very fast.

2. The response detected is a measurement of the electrical signals and does not rely on a physiological response like a heart beat or perspiration.

Unlike other biofeedback methods, GeneratorX does not need the contact pads far apart. In fact, it is better to have them very close together.

If the TENS pads are far apart (like we recommend for Spooky Pulse) the ratio of bad cells to good cells between the pads is reduced. If you have severe disease in your lungs, placing the TENS pads on your right wrist and left ankle will mean that most of the distance between the pads is healthy tissue. The hits detected will be hidden by the ‘noise’ of the good cells.

It is like trying to listen to music while having children playing nearby. It is better to be close to the music player so the sound is clearer. So we recommend that the TENS pads be placed as close as possible to the problem area.

There is no limit to how close you can place the TENS pads. There are instances where you can have them 1mm (0.04 inches) apart. In fact, the accuracy of the results become greater the closer you have them.

If you only have bad cells between the pads, the results will be pure and super-accurate. There are fewer good cells to add unwanted signals to the results.

The GX biofeedback preset runs for a little over 6 minutes, depending on your computer speed.

Before commencing the scan, enter text in the Log Name field in the Control tab. This can be a person’s name or other relevant information. The file created will use this text, making record keeping easier later.

For more information on biofeedback scanning, please see the section on Biofeedback Scan in the latest Spooky2 Quick Guide.

GeneratorX

Share this:

10 Comments

  1. Can you add saliva or discharge from the nose between pads

    1. Hi, it is not recommended.

  2. i have a question i did a biofeedback scan and tried to create a program i get an error,what did i do wrong??

    1. Hi, Alan, please send email to our service: [email protected] and our service will help.

  3. Does using Tens pads on acupuncture points work through those channels?

    1. Yes, but it is better to use the TENS cable pins, and low power.

  4. Can anyone contact me and send me a link to my email address how to Use Spooky 2 Central along with Generator X together . I can not find it.
    Please send a link for hardware and software connection and scan/treatment run.
    I want to run a BioFeadback using Spooky Central and and generator X and then run a treatment using both Central with its frequency generator with Generator X together .
    I thought it can be done together and it’s more powerful, but I can not find a link on how to to it
    Can you please send a link to crash _inna @yahoo.com
    Thank you so much for your help.

    1. Hi, for how to use central, please go to this link: https://www.spooky2-mall.com/blog/how-to-set-up-both-hardware-and-software-to-use-spooky-central/
      And to use it with genx, please connect to G1 or G2 on genx. The rest part will be same. You cannot scan with central but you can run its results on it. For how to do genx scan, please go to this link:
      http://www.spooky2videos.com/video/how-to-do-generatorx-biofeedback-scan/
      If you still have any questions, feel free to contact our service online.

  5. Hi what do u do with the scan results? How do u go about running a program with the Bfb results?

    1. Hi, you can run it in different modes like remote, contact or plasma. For how to run scan results, you can go to this blog: https://www.spooky2-mall.com/blog/what-do-we-do-after-we-get-results-from-biofeedback-scan-using-spooky-pulse/

Leave a Reply

Your email address will not be published.