Dark Light

What are the differences between Remote, Contact and Plasma Modes? 19

Share this:

The majority of Spooky2 users will use Remote and Contact Modes. Although these last two ways of working may seem worlds apart, there are only a few important operational differences between them. But Plasma Mode is very different from the others.

Here’s a table that summarizes the differences between all three modes:

Differences Plasma Mode Contact Mode Remote Mode
Transmission Wireless delivery: plasma tube via radio – band, photonic, and scalar energy. Wired delivery: Spooky Hand Cylinders/electrodes via DC electricity. Wireless delivery: Spooky Remote via DNA/scalar energy.
Durations Takes less time: usually three minutes per frequency repeated once a day, or every second or third day. Takes less time: usually three minutes per frequency repeated once or twice a day. Takes more time: usually 1-3 minutes per frequency repeated up to 20 times a day, or even non-stop.
Carriers Spooky Central doesn’t require any carrier because it can transmit direct frequencies. However, it can also use carriers in various very powerful and creative ways. Carrier may be required for deepbody penetration. Dynamic carriers are strongly recommended for added therapeutic effect. Carrier not required – frequencies are received by every cell that contains DNA. But use of a dynamic carrier will add therapeutic effect.
Sweeps Spooky Spectrum sweeps cannot be used with plasma – use the Spooky Central Spectrum Sweep instead – or a carrier sweep.  

Carrier sweeps require Spooky Central. Spooky Spectrum sweeps won’t work due to voltage requirements.

Carrier sweeps need Spooky Central. Spooky Spectrum sweeps are engineered for Remote Mode only.
Inverse+Sync  

Neither this nor Follow Out 1 are used for Spooky Central. This unit requires its own special settings which are always automatically loaded once you dedicate a generator to it (shown earlier).

Quadruples the power of Contact Mode by inverting Out 2’s waveform, doubling its voltage potential, and adding it to Out 1 (doubling the voltage of a signal squares its power). Doubles the power of Remote Mode by inverting Out 2’s waveform and adding its harmonic content to Out 1.

 

As you can see, Remote Mode looks extremely attractive for those who lead busy lives. And there is also the problem that the Spectrum sweeps are not practicable in either Plasma or Contact Modes.

However, there are considerable benefits to be had from mixing your modes, and our recommendation is to do one Plasma or Contact session on the main problem every day, then switch the generator over to Remote Mode. That way, you get the best of both worlds.

And for serious problems, powerful plasma mode is strongly recommended.

For more differences between each delivery method, please check this link:
https://www.spooky2-mall.com/blog/what-is-the-difference-between-each-delivery-method-and-what-has-the-best-efficacy/

Share this:

19 Comments

  1. What is Spooky Central?

    1. The central is our best powerful rife machine, for more details, you can refer to this blog:https://www.spooky2-mall.com/blog/advantages-of-spooky2-central-kit/
      And here is the instruction:https://www.spooky2-mall.com/blog/spooky-central-instructions/

  2. What is a sweep?

    1. Dear friend, for the sweep, the spooky have the Spectrum Sweep or Converge Sweep, for more details, you can check this blog:https://www.spooky2-mall.com/blog/using-spectrum-sweeps/ and https://www.spooky2-mall.com/blog/carrier-sweeps-explained/

  3. On Inverse+Sync . REMOTE…. “Doubles the power of Remote Mode by inverting Out 2’s waveform and adding its harmonic content to Out 1.” What does that mean?

    1. Hi beminglight. The inverse + sync is required in order to combine both outputs to double the voltage potential (boost) on all models of the boost (v1 – v3.1).
      If you use Follow Out 1 which does not invert Out 2, then the two signals will cancel out when processed by the boost.
      Of course, you can still elect to not use inverse + sync, in order to combine two separate distinct outputs into a single output connection.

  4. Hello!
    How do I know my remote is working once it is plugged? How do I make sure?

    Melanie Gallardo
    1. Hello, you can first observe whether the port button on the software control page turns green, and then observe whether the light on the remote is on. Of course, there will be cases where it is not bright, which is related to the frequency you are running. There is one blog that explain in detail: https://www.spooky2-mall.com/blog/how-does-spooky-remote-light/

  5. Hi, I have a friend who has had a vac and is having a temperature reaction a few days later, I have xm, can I do remote covid treatment on her as well as the things that came up in her biofeedback, and can this be done at the same time remotely through xm? Thank you. If not what else can I do?
    Thank you 😊

    1. Hi, you can run remote treatment on your friend. Just need some DNA samples from her, like fingernails. But XM only has one generator, which means that you only run one program treatment on your friend. You cannot run these two at the same time. You could try to run one first and then run the next. And you can also take GX into your consideration, GX owns two generators. Any questions, please feel free to send them to [email protected]. Our customer service are willing to help you at any time:)

  6. Hi Penny, Followed by Kat’s question above, if Kat can combine her friend’s BFB scan result with Covid19 healing to form a new preset chain, will she still need to get a new GenX unit or a single XM can do meet what she wants originally?

    1. Hi, yes, she needs to. Because she needs one generator to run bfb scan results and the other one for other programs. She originally owns only one XM, which is equipped with one generator. So GX will be a better choice, which has two generators to run two different programs. Also, she could buy a single XM:)

  7. If this is supposed to be an explanation, it fails.
    WOT.

    1. Hi, Joe. Sorry to bring you this trouble. If you have any questions about this topic, please feel free to send them to [email protected], our support team will help you have a further check and reply to you ASAP:)

  8. How does Spooky Scalar with a Generator X connected, relate to this (Rife Scalar)?

  9. My question is : What problems does each of these modes work on.
    Can they be used for the same issues.
    Do they have specialties in the targeting of specific problems.
    In this post, I understand mostly the technical aspects but it dosen’t give clear understanding of when to use them.
    Thank you for the help.
    Collette

    1. Hi collette, this blog might help you learn more: https://www.spooky2-mall.com/blog/which-treatment-mode-is-the-best-for-you/, you can also search for the corresponding keywords to find related blogs to help you better understand each mode. Any questions, feel free to contact us by email: [email protected].

  10. What is considered as a carrier?

    1. Hi Mike, Instead of being limited to a fixed carrier, Spooky2 Central can use any carrier frequency. You can check the instructions about Central here: https://www.spooky2-mall.com/blog/spooky-central-instructions/ and feel free to contact us with questions at our email address: [email protected]. Thanks for your understanding and support.

Leave a Reply

Your email address will not be published. Required fields are marked *